Penggunaan bor mesin dengan sistem kontrol elektropnumatik guna peningkatan efisiensi kerja di industri

Jurnal Riset Tindakan Indonesia October 19, 2025 Volume 10, Number 1 5 authors

Abstract

Tujuan penelitian ini yaitu menganalisis pengaruh variasi putaran terhadap laju pengeboran pada mesin bor dengan kontrol elektropneumatik dan mengkaji pengaruh alir udara terhadap laju pengeboran pada sistem yang sama. Metode yang digunakan dalam penelitian ini yaitu eksperimental dan analisis pengaruh kecepatan mesin terhadap debit udara dan waktu rata-rata, dimana alat yang digunakan dalam penelitian ini yaitu mesin gergaji dan las listrik dengan bahan adalah plat besi galvanis dengan tebal 4 mm. Keterbaruan penelitian ini yaitu mencari pengaruh kecepatan, waktu dan debit udara dalam aplikasi mesin bor, hasil yang didapt dalam penelitian ini yaitu pada saat pengeboran pada variasi putaran (1 putaran, 2,5 putaran, 4 putaran, 5,5 putaran, 7 putaran, 8,5 putaran) diperoleh waktu masing-masing 4,27 dtk, 2,52 dtk, 1,64 dtk, 1,54 dtk, 0,82 dtk, 0,75 dtk dan semakin besar variasi putaran (8,5 putaran) yang dipakai maka semakin tinggi kecepatannya (0,0466 m/dtk) dan semakin besar debit udara (7,272 ltr/mnt) yang digunakan.

Authors

  1. Muammar Alfin Sagala

    Universitas Al-Azhar Medan

  2. Zufri Hasrudy Siregar

    Universitas Al-Azhar Medan

  3. Edy Syahputra Saragih

    Universitas Al-Azhar Medan

  4. Mawardi Mawardi

    Universitas Al-Azhar Medan

  5. Andri Ramadhan

    Universitas Al-Azhar Medan

Keywords

No keywords available

References

  1. Benyettou, R., Belkadi, A., Zitoune, R., & Ayad, R. (2022). Assessment of induced delamination during drilling of composite laminates: Impact of spindle speed and feed rate. Journal of Manufacturing Processes, 82, 1–12. https://doi.org/10.1016/j.jmapro.2022.09.026
  2. Cao, J., Zhang, Y., & Li, F. (2024). Experimental and simulation investigation on the impact of airflow dynamics in pneumatic drilling hammers. Journal of Petroleum Science and Engineering, 237, 112312. https://doi.org/10.1016/j.petrol.2024.112312
  3. Faizin, A., Wicaksono, H., & Sari, N. P. (2022). Design and analysis of pneumatic drilling fixture using microcontroller-based control system. Proceedings of the ATASEC Conference. https://doi.org/10.1109/ATASEC.2022.368488163
  4. Han, X., Liu, J., & Zhao, Q. (2020). Pressure drop characteristics of reverse circulation systems and the effect of gas/air velocity. Advances in Mechanical Engineering, 12(6), 1–10. https://doi.org/10.1177/1687814020925235
  5. Li, D., Tong, L., Huang, Z. et al. Numerical analysis on the drilling force of pneumatic impactors under different working conditions and structural parameters. Sci Rep 15, 33405 (2025). https://doi.org/10.1038/s41598-025-18751-y
  6. Mahendraker, A. R. (2014). Automation of drilling process using electro-pneumatics system. International Journal of Science and Research (IJSR), 3(10), 361–365. https://www.ijsr.net/getabstract.php?paperid=OCT1489
  7. Muthukkaruppan, M., & Manoj, K. (2007). Low cost automation using electro pneumatic system – An online case study in multistation part transfer, drilling and tapping machine. In Proceedings of the 24th International Symposium on Automation and Robotics in Construction (ISARC 2007). Construction Automation Group, Indian Institute of Technology Madras.
  8. Nazarova, O., Klymenko, A., & Kolisnyk, A. (2024). Mechatronic automatic control system of electropneumatic manipulator: Laboratory stand and modelling. Scientific Reports, 14(1), 5238. https://doi.org/10.1038/s41598-024-56672-4
  9. Oladapo, B. I., Balogun, V. A., Adeoye, A. O. M., Olubunmi, I. E., & Afolabi, S. O. (2017). Experimental analysis of electro-pneumatic optimization of hot stamping machine control systems with on-delay timer. Journal of Applied Research and Technology, 15(4), 356–364. https://doi.org/10.1016/j.jart.2017.03.006
  10. Pollák, M. (2022). Research into the impact of spindle speed and feed rate changes on deep drilling tool life and machining efficiency. Machines, 10(4), 268. https://doi.org/10.3390/machines10040268
  11. Qi, Bo & Cao, Pinlu & Yang, He & He, Wenbo & Wang, Mengke & Chen, Baoyi & Bo, Kun & Zheng, Zhichuan. (2021). Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD). Geofluids. 2021. 1-12. 10.1155/2021/3586572.
  12. Rathod, D. K., & Gawande, S. H. (2016). Automation of drilling machine using electro pneumatic system. International Research Journal of Engineering and Technology (IRJET), 3(1), 552–556. https://jart.icat.unam.mx/index.php/jart/article/view/767
  13. Świder, J. (2005). Programmable controller designed for electro-pneumatic systems. Control Engineering Practice, 13(8), 1027–1035. https://doi.org/10.1016/j.conengprac.2005.01.012
  14. Zhang, Y., Chen, H., & Liu, D. (2025). The impact of drilling parameters on drilling temperature and implications for tool life. Applied Sciences, 15(15), 8568. https://doi.org/10.3390/app15158568